


67.2V5A millet electric balance car charger UL CE 3C certification 67.2v lithium battery smart pulsating fast charge
此款充电器适用于使用储能电池为动力的各种设备、工具:
This charger is suitable for all kinds of equipment and tools using energy storage battery as power
1 交通工具:电动自行车和电动摩托车;
Transportation: electric bikes and scooters;
2 机器人:电动玩具和工业用电动机器人;
Robots: Electric toys and industrial electric robots;
3 其他实用型电动工具.
Other practical power tools.
No. |
项目名称 Item |
项 目 参 数 Item parameters |
备 注 Remarks |
1 |
输入电压 Input voltage |
额定电压: 110Vac/220Vac Rated voltage:110Vac/220Vac 调整范围:100-120Vac/200-240Vac Adjustment range: 100-120Vac/200-240Vac |
|
2 |
输入频率 Input frequency |
额定频率:50/60Hz Rated frequency:50/60Hz 调整频率:47-63Hz Adjust frequency:47-63Hz |
|
3 |
最大输入电流 Max input current |
当输入电压为100VAC时,最大输入电流为7A when the input voltage is 100VAC,the maximum input current is7A. |
|
4 |
浪涌电流 Surge current |
在环境温度为25℃,当输出为额定负 载,输入220Vac冷态起动时的最大浪 涌电流<50A。 At ambient temperature of 25℃,when the output is rated negative load,input the maximum wave at 220VAC cold start,the surge current is less than 50A. |
|
输出特性(Output Characters)
No. |
项目名称 item |
项 目 参 数 Item parameters |
备 注 remarks |
|
1 |
输出功率 Output power |
输出电压:67.2V Output voltage:67.2V 最大充电电流:5A Max.Charge current:5A 风扇转灯电流0.5A Fan turn lamp current0.5A 最大输出功率:336W Max. Output Power:336W |
|
|
2 |
负载特性
Load characteristics |
空载电压:67.2V No load voltage:67.2V 最大充电电压:67.2V Max.Charge Voltage:67.2V 线性调整:±0.2V Line regulation : ±0.2V 负载调整:±5% Load Regulation;±5% |
|
|
3 |
效率 efficiency |
当输入电压为220Vac,输出最大负载时,效率≥90%。(TYP) When the input voltage is 220VAC and the maximum load current output ,the efficiency more than90% |
|
|
保护功能及其它(Protection Function and Others)
No. |
项目名称 item |
项 目 参 数 Item parameters |
1 |
输入欠压保护 Under voltage protect |
输入电压<100Vac时,充电器无输出;输入电压条件满足时可自动恢复正常。 When the input voltage is less than 100VAC, the charger has no output; When the input voltage condition is satisfied, it can automatically return to normal. |
2 |
输出短路保护 Output short circuit protection |
该电源在输出短路解除后,重新拔插AC插头充电器能恢复正常工作。 After the output short circuit is removed, the charger can resume normal operation by pulling out and in AC plug . |
3 |
输出过流过温保护 Output overflow temperature protection |
过流过温故障排除后,电源将自动恢复正常工作。 The power supply will automatically return to normal operation after the over-flow temperature fault is removed. |
4 |
输出过压保护 Output over voltage protection |
当输出电压超过额定电压时,电源将保护,故障排除后需重新上电。 When the output voltage exceeds the rated voltage, the power supply will be protected and the power need to be restored after trouble shooting. |
5 |
输出低压保护 Output low voltage protection |
当电池电压<30V时,充电器保护, 故障解除且重启充电器恢复工作。 When the battery voltage is less than30V, the charger is protected,the fault is removed and the charger restarts to work. |
6 |
输出反接保护 Output reverse connection protection |
当输出端子反接时,充电器保护,重新拔插AC插头充电器能恢复正常工作。When the output terminal is reversely connected, the charger will be protected and the charger can resume normal operation by re plugging the AC plug |
7 |
防护等级 Protection class |
IP30 (室内使用)(Indoor use) |
环境要求(Environment Requirement)
No. |
项目名称 item |
项 目 参 数 Item parameters |
备注 remarks |
1 |
工作温度 Work Temperature |
-20℃~+45℃ |
|
2 |
储存温度 storing temperature |
-20℃至85℃ |
|
安全及EMC要求(Safety and EMC Requirement)
No. |
项目名称 item |
标准/测试条件 Standard/Test conditions |
备注 remarks |
|
1 |
耐压测试 high-voltage insulation test |
输入-输出 Input-output |
1800Vac/60s ≤5mA |
|
2 |
绝缘电阻 Insulation resistance |
输入-外壳 Input- outer shell |
≥100MΩ@500Vdc |
|
输出-外壳 Output-outer shell
|
≥100MΩ@500Vdc |
|||
3 |
漏电流 Leakage Current |
<5mA |
|
|
4 |
认证机构 Certification authority |
CE |
|
|
5 |
认证标准 Certification standards |
EN60950
|
|
指示灯状态说明及充电示意图(Indicator Light Status Description and Charging Schematic Diagram)
No. |
充电状态 Charge state |
指示灯状态 Indicator light status |
备注 remarks |
1 |
空载 no-load |
LED1:绿灯常亮Full of green light LED2:红灯常亮Full of red light |
|
2 |
正常充电 normal Charging |
LED1:红灯常亮Full of red light LED2:红灯常亮Full of red light |
|
3 |
充满full |
LED1: 绿灯常亮Full of green light LED2:红灯常亮Full of red light |
|